These items might interest you:
See all results
Your bag
(0) items
S-M7 Deed Helmet ECE 22.06
Supertech Smoke Lens
S-M5 Venture Visor
Supertech Roll Off Film
Supertech Goggles Strap
S-M3 Youth Crown Pad
S-M8 Factory Visor
S-M5 Rover Visor
Supertech M10 Carbon Meta2
Supertech M10/M8 Chin Vent
Supertech M10/M8 Chin Vent
S-M8 Contact Visor
Supertech M10 Ampress Helmet ECE 22.06
S-M3 Fray Helmet ECE 22.06
S-M7 Cast Helmet ECE 22.06
Supertech M10 Padding Replacement Kit
Vision Youth Mirror Lens
Supertech Racing Perimeter Seal Tear Off
Supertech Goggles Strap
S-M5 Bond Visor
Supertech M10/M8 Rear Vent Frame
Supertech M10/M8 Chin Vent Frame
S-M8 Radium Visor
Limited Edition Supertech M10 Daytona 23 Visor
S-M5 Replacement Cheek Pads
S-M7 Fuse Helmet ECE 22.06
S-M7 Solid Visor
S-M7 Ear Pads Set
S-M3 Heat Visor
Supertech M10 Era Visor
Yamaha S-M3 Visor
Vision Dual Pane Youth Lens
Supertech Roll Off Film
S-M5 Solar Flare Visor
FAQs
For motocross helmets in the United States, look for the DOT mark indicating compliance with FMVSS 218. Many off‑road helmets also carry ECE 22.06 certification, which reflects updated impact and rotational assessments; both are widely recognized in the market. Always check your series or event rules if you race, as organizers may specify accepted standards.
Goggles are typically built with impact‑resistant polycarbonate lenses; some models reference the EN 1938 standard for motorcycle eye protection. For shopping by category, explore our MX helmets and goggle accessories.
Your MX helmet should feel evenly snug around the crown and cheeks without hot spots or pressure points; it shouldn’t shift when you shake your head. When you add goggles, the foam should seal uniformly to your face without pinching your nose, and the strap should sit flat around the shell, under the peak. If you wear glasses, choose “OTG” (over‑the‑glasses) goggles and confirm the helmet’s eye‑port provides adequate clearance.
Try the helmet and goggles together in a riding position to confirm field of view, ventilation through the chin bar, and that the peak doesn’t interfere with goggle placement.
MX helmets use a large eye‑port for goggles, an extended chin bar for airflow and roost protection, and a peak to help with sun and debris; ventilation is prioritized for lower‑speed, high‑effort off‑road riding. Street helmets typically have an integrated face shield, more aerodynamic shells, and closed vents for sustained highway speeds.
Choose an MX helmet for dirt, trail, and track riding with goggles. For mixed pavement/dirt use, confirm the helmet style and eye protection match your primary environment.
Select lens tints for light conditions, and choose a vision‑clearing system based on debris and mud. General guidance:
| Conditions | Lens tint | System |
|---|---|---|
| Bright sun | Smoke/gray or mirrored | Standard with tear‑offs |
| Overcast/woods | Yellow/amber for contrast | Standard or tear‑offs |
| Mud/wet races | Clear | Roll‑offs for continuous clearing |
| Night | Clear only | Standard |
Note: some venues restrict disposable tear‑offs—check local rules. Find films, canisters, and spare lenses in goggle accessories.
Remove pads and liners (if detachable) and hand‑wash with mild soap; rinse thoroughly and air‑dry out of direct heat. Clean the shell and goggle lens with warm water and a soft cloth; avoid solvents and abrasive cleaners. Let foam and straps dry completely before storage.
Replace your helmet after any significant impact or around five years of regular use, as materials and EPS liners age over time. Inspect straps, rivets, and the shell periodically; replace scratched lenses and worn goggle foam for optimal vision and seal. For peaks, screws, and spares, see MX helmet accessories.
